Polaris Pb4 Booster Pump Wiring Diagram

Posted By admin On 26/05/19

12345678910111213141516171819202122232425262728293031323334353637383940

Thought I had it wired correctly per the diagram but sparks flew. Wiring Problems For A Polaris Pb4-60. I have a PB4-60 booster pump that I need to.

  • This is a image galleries about Pb4 Booster Pump Repair.You can also find other images like wiring diagram, parts diagram, replacement parts, electrical diagram, repair manuals, engine diagram, engine scheme, wiring harness, fuse box, vacuum diagram, timing belt, timing chain, brakes diagram, transmission diagram, and.
  • Polaris PB4-60 Pool Cleaner Booster Pump Parts List and Diagram Polaris PB4-60 Booster Parts Diagram Polaris PB4-60 Booster Pump.
MAXIMUM WIRE SIZE AND MAXIMUM OVERCURRENT PROTECTION*
Branch Fuse AMPs
Class: CC, G, H, J, K, RK, or T
230 VAC
15A
*Assumes three (3) copper conductors in a buried conduit and 3% maximum voltage loss in branch circuit. All National Electrical Code
local codes must be followed. Table shows minimum wire size and branch fuse recommendations for a typical installation per NEC.

3.2.1 Electrical Wiring

The pump motor must be securely and adequately
before attempting to connect to an electrical power
2.
drop during the start-up and operation of the
3.
grounding or short-circuits. Sharp edges on
wire nuts from loosening, tape them using a
insulating tape. For safety, and to prevent entry
of contaminants, reinstall all conduit and terminal
conduit box.
To configure the internal wiring of the pump motor
for the correct voltage, refer to the diagram on the
5.
may exceed 15 amps on 115 VAC voltage line. It
used for the pump connected to 115 VAC.
The booster pump motor is factory wired for 230
volts, but can be wired for either 115 or 230 volts.
the name plate located on the back of the motor or
From
Filtration Pump
Typical Equipment Layout
PB4-60 Booster Pump
Table 1. Maximum Wire Size and Overcurrent Protection
Voltage
208-230 VAC
20A
)
, ETL
) electrical
®
LXi
Heater
Pool Filter
Installation and Operation Manual
115 VAC
12 AWG
(3.3mm
(3.3mm
2
7.
A separate time clock (in addition to the filtration
On/Off functions of the booster pump. A manual
8.
on at least a half an hour after the pool filtration
half an hour before the filtration pump shuts off.
Periodically check the time clock settings to make
3.3

Plumbing

Be careful not to overtighten any pipe fitting on the
inlet or outlet of the booster pump. Overtightening

3.3.1 Requirements

The Polaris Booster Pump requires a dedicated
return line. Plumb the booster pump into the system so
that it always receives flow from the filtration pump.
To ensure proper function of the pump and the cleaner,
refer to Figure 2 and adhere to the following guidelines
1.
inducing equipment.
of 3 feet
Plumbing
1, 2 or 3*
Spa
ENGLISH
Voltage
208-230 VAC
10 AWG
)
2
NOTE
of all air inducing equipment.
Pump
System
Page 7
115 VAC
)
(5.3mm
2

Polaris Pb4 Booster Pump Motor

(NEC
®
To
  • Quick Links:

Also See for Polaris PB4-60

Related Manuals for Polaris PB4-60

  • Water Pump Polaris TBM 200 LH Series Installation And Maintenance Manual
    8” - type pho / pbo / pvo electro-submersible pump (50 pages)

Related Content for Polaris PB4-60

The Polaris Booster Pump supplies high pressure
water to the Polaris pool cleaner. It is not self-
filtration pump is also running. Running the
damage the booster pump. Improper operation

Important Safety Instructions

When installing and using this electrical
always be followed.
2. WARNING — To reduce the risk of injury, do
they are closely supervised at all times.
permanently installed pools and may also be
not use with storable pools. A permanently
ground or in a building such that it cannot be
pool is constructed so that it may be readily
its original integrity.
Booster Pump should always be
5. A solid copper bonding conductor not smaller
connected from the accessible wire connector
pool, spa or hot tub structure and to all
piping within 5 ft (1.5 m) of the inside walls of a
is installed within 5 ft of the inside walls of the
6. SAVE THESE INSTRUCTIONS.
Note: Plumb the booster pump up-
From
Filtration Pump
Pump
2
Heater
The motor comes wired for 240 volts. The booster
volts. To rewire, follow the instructions on the
the 'sizing' plate on the side of the motor.
A separate time clock (in addition to the filtration
the 'On' and 'Off' functions of the booster pump.
If a time clock is used, it should be set to turn on
filtration pump is turned on and turn off the
Polaris pb4 booster pump repair
cleaner at least one half hour before the filtration
pump shuts off. The Polaris will clean the pool in
and the amount of debris. Periodically check the
time clock settings to make sure they are properly
Installation with a Heater
If the filtration system has a heater, the booster
no closer than three feet downstream from the
diagram). DO NOT TAP THE BOOSTER PUMP
HEAT SINK PIPE THAT COMES DIRECTLY OUT
Installation with a Solar System
always in the water flow (see the diagram below).
the entire water flow at certain times. Care must
'NON-FLOW' pipe when the solar heating system
the system. This override will shut the booster
Minimum
Plumbing
Options
1, 2 or 3
Spa
Pump
To
Chlorinator

Advertisement

Also See for Polaris PB4-60

Polaris PB4-60 Installation And Operation Manual40 pages

Related Manuals for Polaris PB4-60

Summary of Contents for Polaris PB4-60

  • Page 1: Important Safety Instructions

    Polaris Booster Pump Installation Instructions The Polaris Booster Pump supplies high pressure Electrical Hook-up water to the Polaris pool cleaner. It is not self- The motor comes wired for 240 volts. The booster priming and should not be running unless the pump motor may be wired for either 120 or 240 filtration pump is also running.
  • Page 2 If the Polaris will not run or runs slowly Checking Water Flow while the solar heating system is on, contact our Once the system is plumbed, it is important to Customer Service Department. verify that there is sufficient water flow to the booster pump.
  • Page 3 Softube quick connects (part #P133) and optimum level of efficiency. one six-foot section of flexible reinforced hose If the Polaris cleaner does not have UWF (part #P19). pressure restrictors, the UWF restrictor kit (part Universal Wall Fitting Restrictor Kit #10-108-00) is available separately through your participating Polaris dealer.

  • Page 4: Limited Warranty

    Polaris Pool Systems warrants the PB4-60 Booster Pump it manufactures, including all parts and components thereof, to be free of defects in material and workmanship. If you have a question regarding your Polaris Booster Pump, please feel free to call or write us. Be sure to include the serial number of your unit.